[hayitsnik]

Hey guys, hoping those who removed that brick of a brake light can post what they did to make it look better - and how the install was?

Thanks!

 

[Lyoko]

http://www.hondarebel3forum.com/forum/129-appearance-modifications/1841-backlight-mod.html

 

[Lyoko]

http://www.hondarebel3forum.com/forum/617-electrical/3473-replaced-brick.html

 

[nosinut]

This is what I did. Had to cut up the old tail light harness in order to keep the connectors. Also had to modify the fender supports in order to hold the blinker stems. Overall it was a fun mod!

 

[SchnieCo]

This is what I did. Had to cut up the old tail light harness in order to keep the connectors. Also had to modify the fender supports in order to hold the blinker stems. Overall it was a fun mod!

Nosinut - I've been looking at the same setup. Can you give some detail regarding what you had to do as far as cutting up the tail light / modifying fender supports?

 

[hulksmash]

Bike Gallery

Parts:

Tail Light

Turn Signals

ELFR-1-H Electronic LED Flasher Relay 4-Pin Honda

 

[JaviRebel]

Bike Gallery

Parts:

Tail Light

Turn Signals

ELFR-1-H Electronic LED Flasher Relay 4-Pin Honda

Nice setup!

 

[dispo]

http://www.hondarebel3forum.com/forum/129-appearance-modifications/7370-my-turn-change-brick.html

For me the main challenge was finding parts I liked as I decided to use a road legal light which reduced my choices a lot.
The only other challenge was fabricating the bracket which was made easier by using aluminium rather than steel.

The one part I didnt like was that I had to cut the wires to the lamp as they are fixed and not on connectors.

I have now also coloured the bracket black and am very happy with it.

 

[nosinut]

This is what I did. Had to cut up the old tail light harness in order to keep the connectors. Also had to modify the fender supports in order to hold the blinker stems. Overall it was a fun mod!

Nosinut - I've been looking at the same setup. Can you give some detail regarding what you had to do as far as cutting up the tail light / modifying fender supports?

I cut the harness so that I could still use the OEM connectors that go under the seat. As far as modifying the fender supports goes, it's not for the squeamish, haha. I drilled out the threads in order to fit the stem through. Then I ground down the backside of the support in order to be able to catch a nut on the stem. I also has to drill some holes and put grommets in them in order to run the harness between the fender and support. Hope that helps!

 

[Codrin Marius]

Daillight pics

This is what I did. Had to cut up the old tail light harness in order to keep the connectors. Also had to modify the fender supports in order to hold the blinker stems. Overall it was a fun mod!

Hi,



I want to use the same back light and 2 bullet signal lights. Can you take some daylight photos from the side and back to see where you put them exactly?


Thanks!

 

[SLI]

Plug and play tail light and indicators, no cutting or splicing required.

 

[Kenny G]

Plug and play tail light and indicators, no cutting or splicing required.

I want that tail light and blinkers.

Kenny G

 

[SLI]

We're going to be twins hahahahha. Those parts are top notch and built heavy duty!

I want that tail light and blinkers.

Kenny G

 

[Json_Blob]

https://www.hondarebel3forum.com/fo...0169-jsons-blober-500-facelift-completed.html

 

[Kenny G]

We're going to be twins hahahahha. Those parts are top notch and built heavy duty!

SLI,

Can you give me a better link to the tail light, please?

Kenny G

 

[SLI]

I linked it for you in that other thread.

 

[Kenny G]

I linked it for you in that other thread.

That links me to their web page but not the tail light.

Kenny G

 

[Kenny G]

That links me to their web page but not the tail light.

Kenny G

I found the correct link, Thank You!

Kenny G

 

[Kenny G]

I found the correct link, Thank You!

Kenny G

SLI

I ordered the tail light, but didn't know how to find turn signals to fit.

Why don't the Honda OEM turn signals work with the tail light?

Kenny G

 

[kmfpo]

Plug and play tail light and indicators, no cutting or splicing required.

How exactly do you power these if there is no cutting or splicing? Can you elaborate on plug and play? Are you saying that it has wires long enough to replace the factory wires and plugs right into the harness under the seat?